In this article, we will guide you through the process of unboxing and setting up the SawStop 3 HP Industrial Cabinet Saw. This powerful saw is a valuable addition to any woodworking shop, and we will provide step-by-step instructions to ensure a smooth assembly process.
Before we dive into the assembly process, it is essential to read the owner’s manual thoroughly. The manual contains detailed instructions that will help you throughout the assembly. Additionally, the video referenced in this article will give you additional tips and insights to make the setup process even smoother.
Unboxing and Inventory
To begin, unbox the saw and take an inventory of all the parts. Lay them out on a table so that they are easy to see and identify. Once this is done, proceed to remove the shipping oil from the cast iron components. You can use butcher’s bowling alley wax to wipe down the cast iron and protect it.
Attaching the Extension Wing
The first step in the assembly process is attaching the extension wing. Start by propping the wing on a stool or similar surface. Take note of the slight bevel on one side of the wing. Ensure that this side is facing the front of the saw. Use the hardware provided to attach the extension wing, making sure it is perfectly flush with the table top.
Installing the Rails for the Fence
Next, it’s time to install the rails for the fence. Follow the instructions provided in the manual to attach the front and back rails. Start by attaching the front rail, leaving it slightly loose. Then, lift the rail and attach it using another bolt. Finally, secure the front rail by attaching the third bolt.
Repeat the same process for the back rail. Use the longer bolt, washer, lock washer, and nut provided with the rails. Once the rails are attached, move on to the next step.
Attaching the Leg Support Brackets and Extension Table
Attach the leg support brackets to provide stability to the extension table. Then, attach the extension table adjustment bracket. Drop the extension table in place, aligning the adjustment screw with the threaded hole in the cast iron extension wing. The leg support brackets will help support the weight of the extension table while you attach it.
Open the motor cover to gain access to the adjustment screw. Use the bolts to attach the rail to the extension table. Do not tighten the bolt at the end just yet, as it will be done after the legs are attached.
Attaching the Legs and Leveling Feet
Next, attach the legs to the leg bracket and extension table. Adjust the extension table to be flush with the extension wing, and then tighten the bolts on both the front and back rails. Adjust the leveling feet to ensure they are in contact with the floor, and then tighten the bolts that connect the legs to the leg brackets.
Installing the Main Tube and Fence
Place the main tube on the front rail and lock it in place using the provided bolts. Hand tighten the bolts for now. Pull the main tube away from the front rail and drop the fence in place. Attach the handle and lock it in place. Make sure there is about a sixteenth of an inch of space between the front rail and the white nylon guide plate when the fence is locked down.
To achieve this, cut a spacer measuring 11/16 of an inch and hold it between the front rail and the main tube. Push the main tube into position and lock it in place. Repeat the same process on the right side of the fence, making adjustments as necessary to ensure the perfect fit.
Wiring the Saw
Wiring the saw is a straightforward process. Thread the wire through the terminal box, and then use a vinyl insulated spade to attach the wires. Follow the color code provided to ensure the correct connections. Once the wiring is complete, double-check that the blade is tight and spins freely without any obstructions.
Safety System Analysis
When you first turn on the main power switch, the safety system will perform an analyzation routine to ensure proper operation. Any issues with the system will be indicated by a red light. If the routine is completed without any problems, you should not see a red light.
Conclusion
That concludes the unboxing and assembly process for the SawStop 3 HP Industrial Cabinet Saw. While there may be some fine-tuning and adjustments necessary, referring to the manual and becoming familiar with the saw will help you make those small adjustments. We hope you found this guide helpful, and we look forward to seeing you next time!
Note: The main keyword used throughout this article is “SawStop 3 HP Industrial Cabinet Saw.”
